ATX Power Supply with TFX Form Factor
FSP200-60SAV-B P/N: 9PA2004500
 PS-TFX-FSP200-60SAV

Down Load:

Dimension: (WxDxH)

  • 86 x 65.5 x 174.9 mm

  • 3.39 x 2.58 x 6.89 inch

  • 3-1/4 x 2-19/32 x 6-7/8 inch

Connectors:

  • 1x 20-pin Main Connector

  • 1x   4-pin (P4 2x2)

  • 2x   4-pin Peripheral / IDE Power

  • 1x   4-pin Floppy Power

Features:

  • Complied with TFX12V standard

  • High efficiency and reliability

  • Remote On/Off function

  • Internal 12V DC fan included

  • Noise Killer (Thermal fan speed control function)

  • Low noise and ripple

  • Complies with FCC part 15 subpart J Class B and CISPR 22 Class B

  • Output over voltage, short circuit, and over current protection

  • 100% Hi-pot, ATE, and burn-in tested

  • Re-settable power shut down

  • Approved by UL 1950, CSA C22.2 Level 3, TUV EN60950, NEMKO (CB Report)

Specification:

  • Temperature Range: Operating 0° C ~ +50° C on full load; storage & shipping -20° C ~ +65° C

  • Humidity: 90% on operating and 95% on storage

  • Dielectric Withstand: Input to frame ground 1800V AC for 1 second

  • Efficiency: 60% at minimum measured at nominal AC main voltage and frequency with maximum load on all output

  • Rise Time: Less than 20ms on all output

  • Hold-up Time:16.6ms minimum at nominal input voltage

  • Power Good Signal: Power on delay time 100 ms to 500 ms, off delay 1ms minimum (TTL and CMOS compatible)

  • Leakage Current: Less than 3.5mA

  • MTBF: 100,000 hours on maximum load at +25° C degree

  • Dimension (WxHxL): 86x65.5x174.9mm/3.4"x2.5"x6.7" inches

Input Characteristics

  • Input Range: 95~132/190~264V AC, Manual selection

  • Frequency: 47~63Hz

  • Input Current: 7A (RMS) @115V AC, 4A (RMS) @230V AC

  • Inrush Current: 50A cold 70A warm measured at 132Vrms/60Hz

Output Characteristics:

Output Voltage Minimum Load Maximum Load Load Reg. Line Reg. Ripple Noise
+3.3V 0.5A 12/16.7A ± 5% ± 1% 50mV P-P
+5V 1.0A 16/13A ± 5% ± 1% 50mV P-P
+12V 2.0A 10A ± 5% ± 1% 120mV P-P
-5V 0.0A 0.2A ± 10% ± 2% 120mV P-P
-12V 0.0A 0.3A ± 10% ± 2% 120mV P-P
+5Vsb 0.0A 2.0 A ± 5% ± 1% 50mV P-P

*+5V and +3.3V total output not exceed 120W
*+3.3V, +5V, and +12V total output cannot exceed 185W
*When +3.3Vis load on 16.7A, the +5V maximum load is 13A
*When +3.3Vis load on 12A, the +5V maximum load is 16A