Redundant EPS 12V 600W Power Supply
 Emacs / Zippy MRM-6600P (P/N: B001790011)
 PS-R2-ZP-MRM-6600P

Down Load:

Dimension: (WxDxH)

  • 150 x 84 x 254 mm
  • 5.91 x 3.31 x 10.00 inch  
  • 5-29/32 x 3-5/16 x 10 inch

Connectors:

  • 1x 24-pin Main Connector
  • 1x   8-pin EPS 12V
  • 1x   4-pin P4 12V
  • 10x   4-pin Peripheral / IDE Power
  • 2x   4-pin Floppy Power
  • 1x   2-pin 3.68mm Buzzer Reset
  • 1x   2-pin 2.54mm TTL Signal

Features:

  • Temperature Range:
    Operating 0°C ~ 50°C
    Storage: -20°C ~ 80°C
  • Humidity:
    Operating: 20%-80%
    Non-Operating: 10%-90%
  • Hold Up Time: 16ms minimum at full load & 90VAC input voltage
  • Dielectric Withstand:
    Input / Output 1500VAC for 1 minute
    Input to Frame Ground 1500VAC for 1 minute
  • Efficiency: 68% Typical, at Full Load
  • Power Good Signal:
    On Delay 100ms to 500ms
    Off Delay 1ms
  • Over Load Protection: 110~150% Max.
  • Over Voltage Protection:
    +5V -> 5.7~6.5V
    +3.3V -> 3.9~4.5V
    +12V -> 13.3~14.5V
  • Over Current Protection:
    5V, 12V, 3.3V 130% +/- 20% at Full Load
    -5V, -12V Short Circuit
  • EMI Noise Filter: FCC Class B, CISPR22 Class B
  • Safety: to meet UL 60950, CSA 22.2 NO/ 60950, TUV IEC 60950
  • Remote On / Off Control
  • Faulty Alarm Methods: LED, Buzzer, TTL Signal
  • Hot-Swappable / Hot-Pluggable Redundancy Function
  • Balance Load Sharing Design
  • Remote Sensing Design
  • Isolation: Built-In in the Power Module
  • Meet IEC-1000-3-2 Class D (Active PFC)

Specification:

  • Output Wattage: 600W
  • Best Solution for: Server, Workstation, Storage System, System, Communication, Networking

  • Dimension: (WxDxH)
    150 x 84 x 254 mm
    5.    91 x 3.31 x 10.00 inch  
    5-29/32 x 3-5/16 x 10 inch

  • Voltage: 90~264 VAC Full Range
  • Frequency: 47 ~ 63 Hz
  • Input Current: 10/5A for 115/230VAC
  • Inrush Current: 80A/150A Max. for 115/230VAC per Power Module
  • Output Characteristics:
    Output
    Voltage    		 Min. Output
    Current    		 Max. Output
    Current    		 Peak Output
    Current    		 Regulation
    Load    		 Regulation
    Line    		 Output Ripple &
    Noise Max. [P-P]
    +5V 1.0 28.00 --- +5%, -4% ±1% 50mV
    +12V 2.0 45 --- +5%, -4% ±1% 120mV
    -5V 0 0.8 --- ±50% ±1% 120mV
    -12V 0 1 --- ±5% ±1% 120mV
    3.3V 1.0 28 --- +5%, -3% ±1% 50mV
    +5VSB 0.1 2.5 --- +5%, -4% ±1% 50mV

    Remarks:
    >

* The power supply is for chassis assembly only and is not allowed to be operated as stand-alone component. Final assembly has to comply with corresponding EMC and safety regulations.