Micro ATX Switching Power Supply
FSP250-60SPV PS3 (PS/3) Type P/N: 9PA2507502
ATX12V for Pentium 4
 PS-PS3-FSP250-60SPV

 Down Load FSP250-60SPV PDF Drawing

Dimension: (WxHxL)
> 150x86x100 mm
> 5.9x3.4x3.9 inch

Connectors:
> 1x 20-pin Main Connector
> 1x 4-pin (P4 2x2)
> 4x 4-pin Peripheral / IDE Power
> 2x 4-pin Floppy Power

 Features:
  • Complied with Micro ATX and ATX12V standard
  • High efficiency and reliability

  • Remote On/Off function

  • Internal 12V DC fan included

  • Noise Killer (Thermal fan speed control function)

  • Low noise and ripple

  • Complies with FCC part 15 subpart J Class B and CISPR 22 Class B

  • Output over voltage, short circuit, and over current protection

  • 100% Hi-pot, ATE, and burn-in tested

  • Re-settable power shut down

  • Approved by UL 1950, CSA C22.2 Level 3, TUV EN60950, NEMKO (CB Report)

Specification:
  • Temperature Range: Operating 0° C ~ +25° C on full load; storage & shipping -20° C ~ +65° C
  • Humidity: 90% on operating and 95% on storage
  • Dielectric Withstand: Input to frame ground 1800V AC for 1 second
  • Efficiency: 65% at minimum measured at nominal AC main voltage and frequency with maximum load on all output
  • Rise Time: Less than 20ms on all output
  • Hold-up Time:16ms minimum at 115V/60Hz and 10.0ms minimum at 230/50Hz
  • Power Good Signal: Power on delay time 100 ms to 500 ms, off delay 1ms minimum (TTL and CMOS compatible)
  • Leakage Current: Less than 3.5mA
  • MTBF: 100,000 hours on maximum load at +25° C degree
  • Dimension (WxHxL): 150x86x100mm / 6"x3.4"x4" inches
    •

    Input Characteristics:

    • Input Range: 115/230Vrms AC ± 10% , Manual selection
    • Frequency: 47~63Hz
    • Input Current: 7A (RMS) @115V AC, 4A (RMS) @230V AC
    • Inrush Current: 60A Max for 264Vrms AC Cold start

    Output Characteristics:
     

    Output Voltage

    		 Minimum Load

    Maximum Load

    Load Reg.

    Line Reg.

    Ripple Noise
    +3.3V 0.3A 12.12/20A ± 5% ± 1% 50mV P-P
    +5V 1.0A 27/21.8A ± 5% ± 1% 50mV P-P
    +12V 0.2A 17A ± 5% ± 1% 120mV P-P
    -5V 0.0A 0.3A ± 10% ± 2% 120mV P-P
    -12V 0.0A 0.8A ± 10% ± 2% 120mV P-P
    +5Vsb 0.0A 2.0 A ± 5% ± 1% 50mV P-P

    * +5V and +3.3V total output not exceed 175W
    * +3.3V, +5V, and +12V total output cannot exceed 235W
    * When +3.3Vis load on 20A, the +5V maximum load is 21.8A
    * When +3.3Vis load on 12.12A, the +5V maximum load is 27A