FLEX ATX Power
Supply
SPI270LE2 by
SPI (Sparkle Power)
PS-FLX-SPI270LE2
Down Load
Dimension:
- WxHxL: 81.5 x 43 x
150 mm
- WxHxL: 3.21 x 1.69
x 5.91 inch
- WxHxL: 3-1/4 x
1-11/16 x 5-15/16 inch
Connectors:
- 1x 20-pin Main Connector
- 1x 4-pin (P4 2x2)
- 2x 15-pin SATA
Power
- 3x 4-pin Peripheral / IDE Power
- 1x 4-pin Floppy Power
Features:
- Complied with Flex
ATX and ATX12V standard
- Active Power
Factor Correction (PFC) meet EN61000-3-2
- High efficiency
and reliability
- Compatible with
European Union Directive 2002/95/EC (Restriction on Hazardous
Substances).
- Remote ON/OFF
function
- Internal 12V DC
fan included
- Noise Killer
(thermal fan speed control function)
- Low noise and
ripple
- Output over
voltage, short circuit, and over current protection
- 100% Hi-pot, ATE,
and burn-in tested
- Re-settable power
shut down
- Complies with FCC
part 15 subpart J class B 115Vac operation, and CISPR 22 class B
at 230Vac operation
- Approved by CUL/UL60950-1,
TUV EN60950-1, NEMKO EN60950-1 (CB Report) CE ,BSMI ,FCC
Specification:
- Temperature Range:
Operating: 0°C ~ +50°C on full load; storage & shipping: -20°C ~
+80°C
- Humidity: 5~90% on
operating,5~ 95% on storage
- Dielectric
Withstand: Primary frame ground 1800V AC for 1 second
- Efficiency:
typical up to 80%
- Rise time: Less
than 20ms
- Hold-up Time: 17ms
minimum at nominal input voltage
- Power Good Signal:
Power on delay time 100 ~ 500ms, off delay 1ms minimum (TTL and
CMOS compatible)
- Leakage Current:
Less than 3.5mA at 264Vac, 50Hz
- MTBF: 100,000
hours on maximum load at +25°C
Input
Characteristics:
- Input Range: 90 ~
264Vac , Full Range Input
- Frequency: 47 ~
63Hz
- Input Current: Max
5A @ 115Vac, 3A @ 230Vac
- Inrush Current: No
damage
Output Characteristics:
|
Output Voltage |
Minimum Load |
Normal Load |
Maximum Load |
Load Reg. |
Ripple Noise |
|
+3.3V
|
0.5A |
8A
|
16A |
± 5%
|
50mV P-P
|
|
+5V
|
0.5A |
9A
|
18A |
± 5%
|
50mV P-P
|
|
+12V1 |
1.0A |
8A
|
16A |
± 5%
|
120mV P-P
|
|
+12V2 |
1.0A |
5A
|
10A |
± 5%
|
100mV P-P
|
|
-12V
|
0.0A |
0.4A
|
0.8A |
± 10%
|
120mV P-P
|
|
+5Vsb
|
0.0A |
1.25A
|
2.5A |
± 5%
|
50mV P-P
|
-
+12V1 and +12V2 total output shall
not exceed 18 A.
-
+3.3V and +5V total output not
exceed 130W
-
Total output for this subject power
supply is 270W
|
|
