FLEX ATX Switching Power Supply
 SPI270LE 270W Flex ATX P/N: 9PA2700702
Active PFC & RoHS Compliant, 80%+ Efficiency
WxHxL: 3.2x1.6x6-inch (81.5x40.5x150mm)
 PS-FLX-SPI270LE
Down Load SPI270LE Drawing

Connectors:
> 1x 20+4-pin Main Connector
> 1x       4-pin P4 (2x2)
> 2x     15-pin SATA Power
> 3x       4-pin Peripheral / IDE Power
> 1x       4-pin Floppy Power

Features:
> Complied with Flex ATX and ATX12V standard
> Active Power Factor Correction (PFC) meet EN61000-3-2
> High efficiency and reliability
> Compatible with European Union Directive 2002/95/EC (Restriction on Hazardous Substances).
> Remote ON/OFF function
> Internal 12V DC fan included
> Noise Killer (thermal fan speed control function)
> Low noise and ripple
> Output over voltage, short circuit, and over current protection
> 100% Hi-pot, ATE, and burn-in tested
> Re-settable power shut down
> Complies with FCC part 15 subpart J class B 115Vac operation, and CISPR 22 class B at 230Vac operation
> Approved by CUL/UL60950-1, TUV EN60950-1, NEMKO EN60950-1 (CB Report) CE ,BSMI ,FCC

Specification:
> Temperature Range: Operating: 0°C ~ +50°C on full load; storage & shipping: -20°C ~ +80°C
> Humidity: 5~90% on operating,5~ 95% on storage
> Dielectric Withstand: Primary frame ground 1800V AC for 1 second
> Efficiency: 80% minimum
> Rise time: Less than 20ms
> Hold-up Time: 17ms minimum at nominal input voltage
> Power Good Signal: Power on delay time 100 ~ 500ms, off delay 1ms minimum (TTL and CMOS compatible)
> Leakage Current: Less than 3.5mA at 264Vac, 50Hz
> MTBF: 100,000 hours on maximum load at +25°C
> Dimensions (LxWxH): 150x81.5x40.5mm /6x3.2x1.6inch

Input Characteristics:
> Input Range: 90 ~ 264Vac, Full Range Input
> Frequency: 47 ~ 63Hz
> Input Current: Max 5A @ 115Vac, 3A @ 230Vac
> Inrush Current: No damage.

Output Characteristics:
Output Voltage Minimum Load Normal Load Maximum Load Load Reg. Line Reg. Ripple Noise
+3.3V 0.5A 8A 16A ± 5% ± 1% 50mV P-P
+5V 0.5A 9A 18A ± 5% ± 1% 50mV P-P
+12V1 1.0A 8A 16A ± 5% ± 1% 120mV P-P
+12V2 1.0A 5A 10A ± 5% ± 1% 100mV P-P
-12V 0.0A 0.4A 0.8A ± 10% ± 1% 120mV P-P
+5Vsb 0.0A 1.25A 2.5A ± 5% ± 1% 50mV P-P

> +12V1 and +12V2 total output shall not exceed 18 A.
 > +3.3V and +5V total output not exceed 130W
 > Total output for this subject power supply is 270W