FLEX ATX Switching Power Supply
 SPI220LE5 220/250W Flex ATX P/N: 9PA220xxxx
Active PFC & RoHS Compliant, 80%+ Efficiency
WxHxL: 3.2x1.7x6-inch (81.5x43x150mm)
 PS-FLX-SPI220LE5
Down Load SPI220LE5 Drawing

Connectors:
> 1x 20-pin Main Connector
> 1x   4-pin P4 (2x2)
> 2x 15-pin SATA Power
> 3x   4-pin Peripheral / IDE Power
> 1x   4-pin Floppy Power

Features:
> Complied with Flex ATX and ATX12V standard
> Active Power Factor Correction (PFC) meet EN61000-3-2
> High efficiency and reliability
> Compatible with European Union Directive 2002/95/EC (Restriction on Hazardous Substances).
> Remote ON/OFF function
> Internal 12V DC fan included
> Noise Killer (thermal fan speed control function)
> Low noise and ripple
> Output over voltage, short circuit, and over current protection
> 100% Hi-pot, ATE, and burn-in tested
> Re-settable power shut down
> Complies with FCC part 15 subpart J class B 115Vac operation, and CISPR 22 class B at 230Vac operation
> Approved by CUL/UL60950-1, TUV EN60950-1 , NEMKO EN60950-1 (CB Report) CE

Specification:
> Temperature Range: Operating 0° C ~ +25° C on 250W output load or 0° C ~ +50° C on 220W output load ; storage & shipping -20° C ~ +80° C
> Humidity: 5 ~ 90% on operating, 5 ~ 95% on storage
> Dielectric Withstand: Primary frame ground 1800V AC for 1 second
> Efficiency: typical up to 80%
> Rise time: Less than 20ms
> Hold-up Time: 17ms minimum at nominal input voltage
> Power Good Signal: Power on delay time 100 ~ 500ms, off delay 1ms minimum (TTL and CMOS compatible)
> Leakage Current: Less than 3.5mA at 264Vac, 50Hz
> MTBF: 100,000 hours on maximum load at +25°C
> Dimensions (LxWxH):150x81.5x43mm /6x3.2x1.7inch

Input Characteristics:
> Input Range: 90 ~ 264Vac , Full Range Input
> Frequency: 47 ~ 63Hz
> Input Current: Max 5A @ 115Vac, 3A @ 230Vac
> Inrush Current: No damage.

Output Characteristics:
Output Voltage Minimum Load Normal Load Maximum Load Load Reg. Line Reg. Ripple Noise
+3.3V 0.5A 7A 14A ± 5% ± 1% 50mV P-P
+5V 0.5A 8A 16A ± 5% ± 1% 50mV P-P
+12V1 1.0A 8A 16A ± 5% ± 1% 120mV P-P
+12V2 1.0A 5A 10A ± 5% ± 1% 100mV P-P
-12V 0.0A 0.4A 0.8A ± 10% ± 1% 120mV P-P
+5Vsb 0.0A 1.25A 2.5A ± 5% ± 1% 50mV P-P

> 220W (50°C): +3.3V, +5V, and +12V total output cannot exceed 207W.
 > 250W (25°C): +3.3V, +5V, and +12V total output cannot exceed 237W
 > +3.3V and +5V total output not exceed 110W
 > Total output for this subject power supply is 250W