FLEX ATX Switching Power
Supply
SPI220LE Flex 220 ATX
P/N: 9PA2201104
Active PFC & RoHS Compliant, 80%+ Efficiency
WxHxL: 3.2x1.6x6-inch (81.5x40.5x150mm)
PS-FLX-xxx
Links:
Connectors:
> 1x 20+4-pin Main Connector
> 1x 4-pin P4 (2x2)
> 2x 15-pin SATA Power
> 3x 4-pin Peripheral / IDE Power
> 1x 4-pin Floppy Power
Features:
> Complied with Flex ATX and ATX12V standard
> Active Power Factor Correction (PFC) meet EN61000-3-2
> High efficiency and reliability
> Compatible with European Union Directive 2002/95/EC (Restriction on
Hazardous Substances).
> Remote ON/OFF function
> Internal 12V DC fan included
> Noise Killer (thermal fan speed control function)
> Low noise and ripple
> Output over voltage, short circuit, and over current protection
> 100% Hi-pot, ATE, and burn-in tested
> Re-settable power shut down
> Complies with FCC part 15 subpart J class B 115Vac operation, and
CISPR 22 class B at 230Vac operation
> Approved by UL60950, CSA C22.2 NO. 60 VDE EN60950, TUV EN60950 or VDE
EN60950, NEMKO EN60950 (CB Report) CE
Specification:
> Temperature Range: Operating 0° C ~ +25° C on 250W output load or 0° C
~ +50° C on 220W output load ; storage & shipping -20° C ~ +80° C
> Humidity: 5 ~ 90% on operating, 5 ~ 95% on storage
> Dielectric Withstand: Primary frame ground 1800V AC for 1 second
> Efficiency: 80% minimum, typical up to 87%
> Rise time: Less than 20ms
> Hold-up Time: 17ms minimum at nominal input voltage
> Power Good Signal: Power on delay time 100 ~ 500ms, off delay 1ms
minimum (TTL and CMOS compatible)
> Leakage Current: Less than 3.5mA at 264Vac, 50Hz
> MTBF: 100,000 hours on maximum load at +25°C
> Dimensions (LxWxH):150x81.5x40.5mm /6x3.2x1.6inch
Input Characteristics:
> Input Range: 90 ~ 264Vac (RMS), Full Range Input
> Frequency: 47 ~ 63Hz
> Input Current: Max 5A (RMS) @ 115Vac, 3A (RMS) @ 230Vac
> Inrush Current: :No damage at cold start
Output Characteristics:
|
Output Voltage |
Minimum Load |
Normal Load |
Maximum Load |
Load Reg. |
Line Reg. |
Ripple Noise |
|
+3.3V |
0.5A |
7A |
14A |
± 5% |
± 1% |
50mV P-P |
|
+5V |
0.5A |
8A |
16A |
± 5% |
± 1% |
50mV P-P |
|
+12V1 |
1.0A |
8A |
16A |
± 5% |
± 1% |
120mV P-P |
|
+12V2 |
1.0A |
5A |
10A |
± 5% |
± 1% |
100mV P-P |
|
-12V |
0.0A |
0.4A |
0.8A |
± 10% |
±1% |
120mV P-P |
|
+5Vsb |
0.0A |
1.25A |
2.5A |
± 5% |
± 1% |
50mV P-P |
|
>
220W (50°C): +3.3V, +5V, and +12V total output cannot exceed 215W
>
250W (25°C):
+3.3V, +5V, and +12V total output cannot exceed 245W
>
+3.3V and +5V
total output not exceed 110W
>
Total output
for this subject power supply is 220W |
|
