FLEX ATX Switching Power
Supply
SPI150FA-REL P/N: 9PA1503441
PS-FLX-SPI150FA-REL
Links:
Dimension (WxHxL):
- 3.21 x 1.59 x 5.91
inch
- 3-7/32 x 1-19/32 x
5-29/32 inch
- 81.5 x 40.5 x 150.0 mm
Connectors:
- 1x 20+4-pin Main Connector
- 1x 4-pin P4 (2x2)
- 2x 15-pin SATA Power
- 3x 4-pin Peripheral / IDE Power
- 1x 4-pin Floppy Power
Features:
- Complied with Flex ATX and ATX12V standard
- Active Power Factor Correction (PFC) meet EN61000-3-2
- High efficiency and reliability
- Compatible with European Union Directive 2002/95/EC (Restriction on
Hazardous Substances).
- Remote ON/OFF function
- Internal 12V DC fan included
- Low noise and ripple
- Output over voltage, short circuit, and over current protection
- 100% Hi-pot, ATE, and burn-in tested
- Re-settable power shut down
- Complies with FCC part 15 subpart J class B 115Vac operation, and CISPR 22 class B at 230Vac operation
- Approved by UL/CUL 60950-1,NEMKO EN60950-1 (CB Report) CE ,FCC,EMC
report
Specification:
- Temperature Range: Operating: 0°C ~ +50°C; storage & shipping: -20°C ~
+80°C
- Humidity: 85% on operating, 95% on storage
- Dielectric Withstand: Primary frame ground 1800V AC for 1 second
- Efficiency: 68% minimum.
- Rise time: Less than 20ms
- Hold-up Time: 17ms minimum at nominal input voltage
- Power Good Signal: Power on delay time 100 ~ 500ms, off delay 1ms
minimum (TTL and CMOS compatible)
- Leakage Current: Less than 3.5mA at 264Vac, 50Hz
- MTBF: 100,000 hours on maximum load at +25°C
Input Characteristics:
- Input Range: 90 ~ 264Vac (RMS), Full Range Input
- Frequency: 47 ~ 63Hz
- Input Current: Max 4A (RMS) @ 115Vac, 2A (RMS) @ 230Vac
- Inrush Current: No damage.
Output Characteristics:
|
Output Voltage |
Minimum Load |
Normal Load |
Maximum Load |
Load Reg. |
Line Reg. |
Ripple Noise |
|
+3.3V |
0.3A |
5A |
10A |
± 5% |
± 1% |
50mV P-P
|
|
+5V |
0.3A |
6.5A |
13A |
± 5% |
± 1% |
50mV P-P
|
|
+12V |
1.0A |
5A |
10A |
± 5% |
± 1% |
120mV P-P
|
|
-12V |
0.0A |
0.25A |
0.5A |
± 10% |
±1% |
120mV P-P
|
|
+5Vsb
|
0.0A |
1.00A |
2.0A |
± 5% |
± 1% |
50mV P-P
|
|
>
+3.3V and +5V total output not exceed 85W.
>
+3.3V , +5V
and +12V total output shall not exceed 150W.
>
Total output
for this subject power supply is 150W |
|
