FLEX ATX Switching Power
Supply
FSP180-50PLA Flex ATX P/N:
9PA1802274
(FSP180-50PLA-R, FSP180-50PLAR)
PS-FLX-FSP180-50PLA
Links:
Dimension (WxHxL):
- 3.21 x 1.59 x 5.91
inch
- 3-7/32 x 1-19/32 x
5-29/32 inch
- 81.5 x 40.5 x 150.0 mm
Connectors:
- 1x 20-pin Main Connector
- 1x 4-pin P4 (2x2)
- 3x 4-pin Peripheral / IDE Power
- 1x 4-pin Floppy Power
Features:
- Complied with Flex ATX and ATX12V standard
- Active Power Factor Correction (PFC) meet EN61000-3-2
- High efficiency and reliability
- Remote ON/OFF function
- Internal 12V DC fan included
- Noise Killer (thermal fan speed control function)
- Low noise and ripple
- Complies with FCC part 15 subpart J class B 115Vac operation, and CISPR 22 class B at 230Vac operation
- Output over voltage, short circuit, and over current protection
- 100% Hi-pot, ATE, and burn-in tested
- Re-settable power shut down
- Approved by UL60950, CSA C22.2 NO. 60950, TUV EN60950 or VDE EN60950,
NEMKO EN60950 (CB Report), CE
Specification:
- Temperature Range: Operating: 0°C ~ +50°C on full load; storage &
shipping: -20°C ~ +80°C
- Humidity: 5 ~ 95% on operating and storage
- Dielectric Withstand: Input to frame ground 1800 VAC for 2 second
- Efficiency: 68% at minimum measured at nominal AC main voltage and
frequency with maximum load on all outputs
- Rise time: Less than 20ms
- Hold-up Time: 17ms minimum at nominal input voltage
- Power Good Signal: Power on delay time 100 ~ 500ms, off delay 1ms
minimum (TTL and CMOS compatible)
- Leakage Current: Not exceed 3.5mA at 264Vac, 50Hz
- MTBF: 100,000 hours on maximum load at +25°C
- Dimensions (LxWxH): 150x81.5x40.5mm/6x3.2x1.6in
Input Characteristics:
- Input Range: 90 ~ 265Vac (RMS), Full Range Input
- Frequency: 47 ~ 63Hz
- Input Current: 4A (RMS) @115Vac, 2A (RMS) @230Vac
- Inrush Current: 50A Max @115Vac, 80A Max @230Vac cold start
Output Characteristics:
|
Output Voltage |
Minimum Load |
Maximum Load |
Peak |
Load Reg. |
Line Reg. |
Ripple Noise |
|
+3.3V |
0.3A |
16.8A |
xxx |
± 5% |
± 1% |
50mV P-P
|
|
+5V |
0.3A |
12.0A |
xxx |
± 5% |
± 1% |
50mV P-P
|
|
+12V |
1.5A |
10.0A |
13A
|
± 5% |
± 1% |
120mV P-P
|
|
-12V |
0.0A |
0.8A |
xxx |
± 10% |
± 2% |
120mV P-P
|
|
+5Vsb
|
0.0A |
2.0A |
xxx
|
± 5% |
± 1% |
50mV P-P
|
|
>
+5V and +3.3V total output
not exceed 61W
> +3.3V, +5V, and +12V total output cannot exceed 165W |
|
