ATX 12V Power Supply
FSP / SPI FSP300THA-B204
 PS-ATX204-300-THA-B204

Links:

Dimension:

  • WxHxD: 150 x 86 x 140 mm
  • WxHxD: 5.9 x 3.4 x 5.5 inch
  • WxHxD: 5-7/8 x 3-3/8 x 5-1/2 inch

Connectors:

  • 1x 20+4-pin Main Connector
  • 1x       4-pin P4
  • 2x     15-pin SATA Power
  • 6x       4-pin Peripheral / IDE Power
  • 1x       4-pin Floppy Power

Features:

  • Complied with ATX12V 2.0 standard

  • High efficiency and reliability

  • Remote On/Off function

  • Internal 12V DC fan included

  • Noise Killer (Thermal fan speed control function)

  • Low noise and ripple

  • Complies with FCC part 15 subpart J Class B and CISPR 22 Class B

  • Output over voltage, short circuit, and over current protection

  • 100% Hi-pot, ATE, and burn-in tested

  • Re-settable power shut down

  • Approved by UL 60950, CSA C22.2 Level 3, TUV EN60950, NEMKO (CB Report)

Specification:

  • Temperature Range: Operating 0° C ~ +25° C on full load; De-rate 2W/C from +50° C to +25° C; storage & shipping -20° C ~ +65° C

  • Humidity: 90% on operating and 95% on storage

  • Dielectric Withstand: Input to frame ground 1800V AC for 1 second

  • Efficiency: 70% at minimum measured at nominal AC main voltage and frequency with maximum load on all output

  • Rise Time: Less than 20ms on all output

  • Hold-up Time: 17ms minimum at nominal input voltage

  • Power Good Signal: Power on delay time 100 ms to 500 ms, off delay 1ms minimum (TTL and CMOS compatible)

  • Leakage Current: Not exceed 3.5mA

  • MTBF: 100,000 hours on maximum load at +25° C degree

  • Dimension (WxHxL): 150x86x140mm/6”x3.4”x5.5” inches

Input Characteristics:

  • Input Range: +/-10% of 115Vrms or 230Vrms, Manual selection

  • Frequency: 47~63Hz

  • Input Current: 7A (RMS) @115V AC, 3.5A (RMS) @230V AC

  • Inrush Current: 80A max cold start, 100A warm measured at 264rms/50Hz

Output Characteristics:

Output Voltage Minimum Load Maximum Load Load Reg. Line Reg. Ripple Noise
+3.3V 0.5A 6/20A ± 5% ± 1% 50mV P-P
+5V 1.0A 20/10.8A ± 5% ± 1% 50mV P-P
+12V1 1.0A 8A ± 5% ± 1% 120mV P-P
+12V2 1.0A 14A ± 5% ± 1% 120mV P-P
-12V 0.0A 0.8A ± 10% ± 2% 120mV P-P
+5Vsb 0.0A 2.0A ± 5% ± 1% 50mV P-P

  • +5V and +3.3V total output not exceed 120W

  • When +3.3V is load on 20A, the +5V maximum load is 10.8A

  • When +3.3V is load on 6A, the +5V maximum load is 20A

  • +3.3V, +5V, +12V1, and +12V2 total output not exceed 280